Your computer may not be starting up anymore because of a problem. If you can’t find any specific reasons why it might not start up again, your files are most likely safe. However, if something has gone wrong and your computer is not working properly, it’s important to keep track of all the possible problems and see if there is anything you can do to fix them.

  1. The hard drive is not spinning If the hard drive is not spinning, it may be due to a number of factors, including a bad disk or drive, a loose cable, or an issue with the power supply. To check if the hard drive is spinning, take the computer to a local computer store and have them test it. If the hard drive is not spinning, it may need to be replaced.
  2. The motherboard is not compatible with your PC If your motherboard is not compatible with your PC, you may need to replace it. This includes computers that are built in the past few years and those that come pre-loaded with Windows 10. Many motherboards now support newer versions of Windows 10 so you don’t have to upgrade as often as you used to.
  3. The graphics card isn’t working properly If your graphics card isn’t working properly, it may be due to a number of factors, including an issue with the power supply or driver installation. To check if the graphics card is working properly, take the computer to a local computer store and have them test it. If the graphics card isn’t working properly, it may need to be replaced or updated.

Ways to Fix PC Won’t Turn On

Check for power supply problems

Many people find it hard to believe, but the most common reason a computer won’t turn on is because they didn’t turn it on in the first place! The first step in troubleshooting an idle computer should be to make sure the computer is turned on. If it isn’t, up and check if there’s any way to fix it.

If there are no lights flashing, no fans running, and nothing appears on the screen, the cause is most likely a power issue. First, examine the entire length of the power cord for cracks and dents or frayed insulation. If any faults or the power plug smells like burnt plastic, it’s most likely that the cord is faulty.

internal wiring

If your new PC gets power but still won’t turn on, you need to check your case for loose or faulty cables. If your PC won’t turn on after it’s built, poorly connected components could be the reason, especially if you’re a novice PC builder. Always make sure they are properly clicked. If you are using a pre-built system, be aware that opening the PC may void your warranty. Safety first! Always disconnect your PC from the power supply before opening it.

Power Button

If your computer doesn’t turn on when you press the power button, it may be because one of the power connectors on your motherboard is not working or the cable that connects it to your motherboard is not properly connected. If the two connectors are not connected, your computer may not be able to get power.

The jumpers on the motherboard must be connected to the power switch wires, which are usually located in the lower right area of ​​the motherboard. Since these pins are usually unlabeled, it’s probably wise to consult your motherboard manual as there should be a good diagram showing what goes where.

let the battery charge

Your laptop won’t turn on. Do you have an outlet?

Don’t worry, because your laptop is probably fine. Your battery is completely discharged, so to get your laptop working again, let it charge for about thirty minutes before trying to turn it on again. ..

Decrypt POST and Beep codes

When you turn on the computer, it may not turn on. Some or all of the internal hardware lights may turn on up or flash and stop suddenly. You can also hear the fans inside the computer turn on. How can you fix a computer that turns on and then turns off?

Some motherboards are equipped with power-on self-test (POST) codes and beeps. These are audible and visual signals that emit a specific signal (beep code) through the system speakers to inform you that the computer has failed POST. If the code is not recognized, it may indicate that there is a problem with the computer’s hardware or software.

Final Words

  1. Check the power cord and outlet. Make sure the outlet is plugged in and the power cord is properly plugged into the outlet.
  2. Check if there is a problem with your computer’s BIOS or motherboard. If there is a problem with your BIOS, you may need to update it.
  3. Check if your computer has been overclocked or if it has been damaged in some way. Overclocking can cause your computer to not turn on, so make sure you have the correct tools to do so and that you are not using an illegal overclocking method.